Shop

ORDERS BY 3PM – SHIP SAME DAY

  • Punch-N-Cut Tool not only cuts rigid poly tubing, but also makes punching holes and inserting 1/4" barbed fittings & emitters almost effortless. All-In-One!  It is a favorite among landscapers and commercial growers. This lightweight all-in-one tool is a great alternative to those frustrating days of keeping track of multiple tools! Punch N' Cut Tool has three major uses:
    • Cutting Tool - Cuts up to .94" mainline tubing with ease.  Also cuts up to 1" PVC Schedule 40 with a little more effort required.
    • PunchTool - Punches holes in 1/2" or larger mainline tubing for 1/4" fittings or emitters to be inserted.
    • Insert Tool - Holds a barbed fitting and certain emitters to make installation easier. Less work for your fingers.
  • Pressure Gauge Kit for Drip Irrigation Kit

    If you would like to test the pressure of an individual line in your drip irrigation system, simply install this kit directly in the specific row or header of your choice.  The pressure gauge included is a 0-100 psi Glycerin Liquid-Filled Gauge.  This kit is compatible with our Irri-Gator Drip Irrigation Garden Kits.
  • Drip Irrigation Parts and Supplies

    A backflow preventer is the effective and economical way to prevent the risk of back-flow contamination from outdoor hose bibb connected devices.  It comes with a 3/4" FHT inlet and a 3/4" MHT outlet. No Teflon tape is required since both ends are hose thread. A standard hose washer is included to make a water tight seal.
  • Groundskeeper II Rake

    $24.95$76.00

    Gardening Supplies

    Groundskeeper II Rake is available in two sizes: The "Gardener" Rake has a 6" head with 8 steel tines and an 18" fiberglass handle weighing less than 2 pounds. The "Full Size" Rake has a 21" head with 28 steel tines and a 55" fiberglass handle weighing only 2 pounds.
  • Pressure Regulator for Drip Irrigation

    Pressure Regulator 30 PSI is a preset pressure regulator with 3/4" FPT (female pipe thread) x 3/4" MPT (male pipe thread).  Made in the USA.
  • Drip Irrigation Figure Eight End Closure

    Figure Eight End Closure for hose O.D. (outside diameter) up to .660".  This fitting is the most common way to end a 1/2" supply line.  Used in our Irri-Gator Landscape-400 Kit.
  • Drip Irrigation Barb Plugs

    Barb Plugs - Dual End A barb plug is used to plug holes from .075" to .225" in 1/2" supply tubing as well as capping off the end of 1/4" distribution tubing or 1/4" dripper line.  Pack of 100 Barb Plugs.
  • Drip Irrigation Barb Plug

    1/4" Barb Plug - Dual End A barb plug is used to plug holes from .075" to .225" in 1/2" supply tubing as well as capping off the end of 1/4" distribution tubing or 1/4" dripper line.
  • Barb Tees for Drip Irrigation Kits

    1/4" Barb Tee to be used with drip irrigation to either connect 1/4" drip tubing or 1/4" distribution tubing to branch off another line. It can also be inserted in 1/2" supply tubing. Use a 1/4" punch tool to make the proper size hole in the supply tubing.
  • Barb Connector for Drip Irrigation Kits

    1/4" Barb Connector to be used with drip irrigation to either connect 1/4" drip tubing or 1/4" distribution tubing to 1/2" supply tubing or to extend the length of 1/4" tubing by acting as a coupling. Use a 1/4" punch tool to make the proper size hole in the supply tubing.  This irrigation method works great in landscaping, hanging baskets, flower pots and garden boxes!
  • Preset Pressure Regulator for Drip Irrigation Systems

    The preset pressure regulator offers exceptional outlet pressure control to provide consistent performance from 1/2 to 12 gallons per minute.  Both inlet and outlet are 3/4" FIPT.  Included in our Gator 2000 Drip Kit due to extra thick industrial strength side walls.  Made in the USA.
  • Drip Irrigation Emitter (100 Pack)

    The .5 GPH Emitter (Pressure Compensating) delivers a consistent output of water, even with changes in pressure due to long runs of drip tubing or elevation changes. These emitters are self-flushing and less likely to clog than non-pressure compensating drippers. A removable top makes cleaning them simple.  
  • Drip Irrigation Emitter

    The .5 GPH Emitter (Pressure Compensating) delivers a consistent output of water, even with changes in pressure due to long runs of drip tubing or elevation changes. These emitters are self-flushing and less likely to clog than non-pressure compensating drippers. A removable top makes cleaning them simple.  
  • Drip Irrigation Filter

    3/4" Filter with Flush Cap and Stainless Steel 150 Mesh Screen.  This filter is 3/4" MPT (Male Pipe Thread) at both inlet and outlet sides.
  • 2 Inch Plastic Filter with Flush Valve - Economy

    • Filtering Element - 155 mesh stainless steel screen
    • Constructed from chemical resistant polypropylene reinforced with fiber glass
    • Pre-molded pressure taps
    • Threaded cover closure - easy to use / no tools required
    • Includes flush valve
    Brand Name: Irritec
  • Coupling for Drip Irrigation Kits

    3/4" Threaded Coupling is used to connect two fittings each with MPT (Male Pipe Thread). Used in our Irri-Gator Landscape-400 Kit.
  • Drip Irrigation Adapter

    1/2" Insert x 3/4" MPT (Male Pipe Thread) Adapter is used to couple a 1/2" hose to a 3/4" FPT (female pipe thread) fitting.  Along with coupling the hose with a threaded fitting, it also reduces or increases in size between a 1/2" opening and a 3/4" opening.
  • Drip Irrigation Fitting

    1/2" Insert In-Line Valve (.620" OD) allows you to control water flow of individual lines.  The valve connects sections of 1/2" Supply Tubing or 1/2" Dripper Line.  A valve can be easily installed directly into an individual row or into the mainline to control the water flow of more than one row.  Requires NO glue or tools for installation.
  • Drip Irrigation Barb Poly Fitting

    1/2" Insert Tee (.620" OD), which is a 1/2" barb x 1/2" barb x 1/2" barb poly fitting, allows you to branch off an additional 1/2″ line from the mainline or for an individual row.  Due to the style and size of the tubing as, a clamp is not typically required.  These fittings and tubing are for low pressure drip systems.
  • Drip Irrigation Barb Poly Fitting

    1/2" Insert Elbow (.620" OD), which is a 1/2" barb x 1/2" barb poly fitting, allows you to make a 90 degree turn while joining together two pieces of 1/2" Supply Tubing or 1/2" Dripper Line.  Due to the style and size of the tubing as, a clamp is not typically required. Used with Drip Irrigation Landscape Kit.
  • Drip Irrigation Fitting

    1/2" Insert Coupler (.620" OD), which is a 1/2" barb x 1/2" barb poly fitting, allows you to join two together pieces of 1/2" Supply Tubing or 1/2" Dripper Line.  Due to the style and size of the tubing as, a clamp is not typically required.  These fittings and tubing are for low pressure drip systems.
  • Dripper Line for Drip Irrigation Kits

    1/2" Dripper Line (.52 ID) with 12" spacing of built-in emitters in a 100' roll. May be used to customize the Irri-Gator Landscape-400 Kit.  Clog resistant.
  • Drip Irrigation Dripper Line

    1/4" Dripper Line with 12" spacing of built-in emitters in a 100' roll. May be used to customize the Irri-Gator Landscape-400 Kit. This dripper line may be used in the following applications:  Dense Plantings, Large Pots, Shrubs and Trees, and Gardens.
  • Drip Irrigation Kit Tubing

    1/2" Rigid Supply Tubing (no orifices) in a  roll for Irri-Gator Landscape-400 Kit. Supply tubing allows you to get water to the desired locations in a conservative manner. You may use 1/2" insert fittings to extend the length of tubing (insert coupler), make a 90 degree angle (insert elbow) or add a row (insert tee) to your system. A punch tool may be used to insert an emitter in the supply tubing at the exact location of a planting. The 1/4" dripper line or 1/2" dripper line with 12" spacing may also be spurred from this supply tubing using 1/4" barbed fittings or 1/2" insert fittings, respectively.
  • Distribution Tubing for Drip Irrigation Kits

    1/4" Distribution Tubing (no orifices) is most often branched off 1/2" dripper line or 1/2" supply tubing to individual plants with a drip emitter at the end. This tubing with no orifices may also be used as the mainline in smaller projects such as hanging baskets or small flower pot projects on decks and patios.

Title

Go to Top