Shop

  • Drip Irrigation Emitter

    The .5 GPH Emitter (Pressure Compensating) delivers a consistent output of water, even with changes in pressure due to long runs of drip tubing or elevation changes. These emitters are self-flushing and less likely to clog than non-pressure compensating drippers. A removable top makes cleaning them simple.  
  • Drip Irrigation Parts and Supplies

    3/4" Hose Swivel attaches to a hose bib, faucet, spigot, hydrant, garden hose or hose threaded parts (like filters and pressure regulators) and accepts fittings with 3/4" male hose threads (MHT).
  • Drip Irrigation Parts and Supplies

    A backflow preventer is the effective and economical way to prevent the risk of back-flow contamination from outdoor hose bibb connected devices.  It comes with a 3/4" FHT inlet and a 3/4" MHT outlet. No Teflon tape is required since both ends are hose thread. A standard hose washer is included to make a water tight seal.
  • Coupling for Drip Irrigation Kits

    3/4" Threaded Coupling is used to connect two fittings each with MPT (Male Pipe Thread). Used in our Irri-Gator Landscape-400 Kit.
  • Drip Irrigation Figure Eight End Closure

    Figure Eight End Closure for hose O.D. (outside diameter) up to .660".  This fitting is the most common way to end a 1/2" supply line.  Used in our Irri-Gator Landscape-400 Kit.
  • Drip Irrigation Kit Tubing

    1/2" Rigid Supply Tubing (no orifices) in a  roll for Irri-Gator Landscape-400 Kit. Supply tubing allows you to get water to the desired locations in a conservative manner. You may use 1/2" insert fittings to extend the length of tubing (insert coupler), make a 90 degree angle (insert elbow) or add a row (insert tee) to your system. A punch tool may be used to insert an emitter in the supply tubing at the exact location of a planting. The 1/4" dripper line or 1/2" dripper line with 12" spacing may also be spurred from this supply tubing using 1/4" barbed fittings or 1/2" insert fittings, respectively.
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • Dripper Line for Drip Irrigation Kits

    1/2" Dripper Line (.52 ID) with 12" spacing of built-in emitters in a 100' roll. May be used to customize the Irri-Gator Landscape-400 Kit.  Clog resistant.
  • Preset Pressure Regulator for Drip Irrigation Systems

    The preset pressure regulator offers exceptional outlet pressure control to provide consistent performance from 1/2 to 12 gallons per minute.  Both inlet and outlet are 3/4" FIPT.  Included in our Gator 2000 Drip Kit due to extra thick industrial strength side walls.  Made in the USA.
  • Regulator / Tee Screen Assembly for Drip Irrigation

    Regulator / Tee Screen Assembly connects drip tubing or distribution tubing to any ¾” garden hose thread water source. This pressure regulator has a maximum operating pressure of 15 PSI. Requires NO glue or tools for installation. To install tape-loc sides, simply turn sleeve counter-clockwise, slip tubing over barb, and turn sleeve clockwise to hand tighten for a secure fit.
  • Distribution Tubing for Drip Irrigation

    Distribution tubing is also referred to as blank drip tubing. It does not have built-in emitters. To be used to bring water to the garden or for the mainline to avoid any unnecessary water usage. This 5/8" distribution tubing may be added to our Irri-Gator Drip Irrigation Garden Kits. All of our perma-loc fittings will work with this tubing.
  • Drip Irrigation Assembly

    Regulator / Screen Assembly connects drip tubing or distribution tubing to any ¾” garden hose thread water source. The pressure regulator has a maximum operating pressure of 15 PSI. Requires NO glue or tools for installation. To install tape-loc side, simply turn sleeve counter-clockwise, slip tubing over barb, and turn sleeve clockwise to hand tighten for a secure fit.
  • Pressure Regulator for Drip Irrigation

    Pressure Regulator 30 PSI is a preset pressure regulator with 3/4" FPT (female pipe thread) x 3/4" MPT (male pipe thread).  Made in the USA.
  • Drip Irrigation Dripper Line

    1/4" Dripper Line with 12" spacing of built-in emitters in a 100' roll. May be used to customize the Irri-Gator Landscape-400 Kit. This dripper line may be used in the following applications:  Dense Plantings, Large Pots, Shrubs and Trees, and Gardens.
  • Distribution Tubing for Drip Irrigation Kits

    1/4" Distribution Tubing (no orifices) is most often branched off 1/2" dripper line or 1/2" supply tubing to individual plants with a drip emitter at the end. This tubing with no orifices may also be used as the mainline in smaller projects such as hanging baskets or small flower pot projects on decks and patios.
  • Drip Irrigation Barb Plug

    1/4" Barb Plug - Dual End A barb plug is used to plug holes from .075" to .225" in 1/2" supply tubing as well as capping off the end of 1/4" distribution tubing or 1/4" dripper line.
  • Barb Tees for Drip Irrigation Kits

    1/4" Barb Tee to be used with drip irrigation to either connect 1/4" drip tubing or 1/4" distribution tubing to branch off another line. It can also be inserted in 1/2" supply tubing. Use a 1/4" punch tool to make the proper size hole in the supply tubing.
  • Barb Connector for Drip Irrigation Kits

    1/4" Barb Connector to be used with drip irrigation to either connect 1/4" drip tubing or 1/4" distribution tubing to 1/2" supply tubing or to extend the length of 1/4" tubing by acting as a coupling. Use a 1/4" punch tool to make the proper size hole in the supply tubing.  This irrigation method works great in landscaping, hanging baskets, flower pots and garden boxes!
  • Drip Irrigation Filter

    3/4" Filter with Flush Cap and Stainless Steel 150 Mesh Screen.  This filter is 3/4" MPT (Male Pipe Thread) at both inlet and outlet sides.
  • Hose-End Tee Filter for Drip Irrigation Kits

    Recommended to filter out particles common in well water that might clog the built-in emitters in drip tubing. This filter has a swivel FHT (female hose thread) inlet and MHT (male hose thread) outlet. The internal mesh screen filter may be removed for cleaning. When using with a drip irrigation garden kit, install this filter between your water source and the regulator/screen assembly included in each drip kit.
  • Drip Irrigation Tubing

    5/8" Drip Tubing with built-in emitters spaced every 12” for saturation coverage of desired area. Designed to ensure an even flow and minimize clogging of built-in emitters. Flow rate is .5 GPM/100’. For use with Irri-Gator Drip Kits. Ideal for uses in vegetable gardens and flowerbeds where the rows are straight.
  • Drip Irrigation Parts and Supplies

    Perma-Loc Tee fitting to be used with any Irri-Gator Drip Tubing or Distribution Tubing. A tee can be used to branch off an additional line from the mainline or for an individual row. Consists of commercial grade, UV resistant plastic. Requires NO glue or tools for installation. To install, simply turn sleeve counter-clockwise, slip tubing over barb, and turn sleeve clockwise to hand tighten for a secure fit.
  • Drip Irrigation System

    Serious gardeners need a serious irrigation system, and the Gator 1000 system offers the perfect solution. Priced at only $192.63, the Gator 1000 is an expandable kit that waters up to 2,000 square feet. That’s as many as ten rows of 100’ each with as much as five feet between them. Have plans to grow a garden even further? No worries. The Gator 1000 can be expanded to provide irrigation to additional rows. You only need a pair of scissors for the installation – no special tools! This drip irrigation system comes with everything that you will need for installation and execution, delivering outstanding performance and quality when you need it the most, in your garden! We know that your garden is important to you, which means that it is important to us!
  • Drip Irrigation Parts and Supplies

    Perma-Loc Coupling to be used to either connect two pieces of Irri-Gator Drip Tubing or to repair an existing line. Consists of commercial grade, UV resistant plastic. Requires NO glue or tools for installation. Gator 100/250/1000 Drip Irrigation Kit Installation Instructions
  • Drip Irrigation System

    For growing flower beds, the Gator 250 Drip Irrigation Kit offers an efficient, affordable irrigation solution. The kit can accommodate gardens of up to 500 square feet, allowing as many as six separate rows spaced as much as four feet from each other and spanning 38 feet in length each. Because kits can be expanded, homeowners can grow their gardens over time without having to purchase an entirely new kit. At a price of only $93.70, the Gator 250 also won’t stretch the family budget. So what are you waiting for? For a happy, healthy, beautiful garden, let our drip irrigation system help you create the garden that you've always dreamed of at a great price!
  • Drip Irrigation Garden System

    For flower beds smaller than 200 square feet, the Gator 100 irrigation kit is a great way to keep soil moist without using excess water. At a cost of only $59.85, the Gator 100 can bring irrigation to flower beds with as many as four separate rows spanning 22’ in length. Each row can be separated from the next by as much as four feet for the Gator 100 to be effective. To create your own small, personal slice of heaven right in your backyard, look no further than the Gator 100. Our irrigation systems will make your life easier and your plants healthier. Get yours today!
Go to Top