- Cutting Tool - Cuts up to .94" mainline tubing with ease. Also cuts up to 1" PVC Schedule 40 with a little more effort required.
- PunchTool - Punches holes in 1/2" or larger mainline tubing for 1/4" fittings or emitters to be inserted.
- Insert Tool - Holds a barbed fitting and certain emitters to make installation easier. Less work for your fingers.
-
Punch-N-Cut Tool not only cuts rigid poly tubing, but also makes punching holes and inserting 1/4" barbed fittings & emitters almost effortless. All-In-One! It is a favorite among landscapers and commercial growers. This lightweight all-in-one tool is a great alternative to those frustrating days of keeping track of multiple tools! Punch N' Cut Tool has three major uses: -
Drip Irrigation Parts and Supplies
A backflow preventer is the effective and economical way to prevent the risk of back-flow contamination from outdoor hose bibb connected devices. It comes with a 3/4" FHT inlet and a 3/4" MHT outlet. No Teflon tape is required since both ends are hose thread. A standard hose washer is included to make a water tight seal. -
Preset Pressure Regulator for Drip Irrigation Systems
The preset pressure regulator offers exceptional outlet pressure control to provide consistent performance from 1/2 to 12 gallons per minute. Both inlet and outlet are 3/4" FIPT. Included in our Gator 2000 Drip Kit due to extra thick industrial strength side walls. Made in the USA. -
Drip Irrigation Filter
3/4" Filter with Flush Cap and Stainless Steel 150 Mesh Screen. This filter is 3/4" MPT (Male Pipe Thread) at both inlet and outlet sides. -
Drip Irrigation Clamps
1" Clamp is a good general-purpose clamp. Diameter Range SAE is 11/16" to 1-1/4" (18mm t0 32mm). This clamp is also referred to as a worm drive hose clamp. -
Drip Irrigation Fitting
1" Insert Tee allows you to branch off an additional 1" line from the mainline or for an individual row. 1" Clamps required (not included). Included in our Gator 2000 Drip Irrigation Kit. -
Drip Irrigation Fitting
1" Insert Plug, which is a 1" insert poly fitting, allows you to end a piece of 1" tubing (ID). A 1" clamp is required (not included) to secure the fitting to the tubing in case pressure is applied. -
Drip Irrigation Fitting
1" Insert Elbow allows you to make a 90° turn in 1" tubing (ID). 1" Clamps required (not included). May be used with our Gator 2000 Drip Irrigation Kit. -
Drip Irrigation Fitting
1" Insert Coupling allows you to join two pieces of 1" tubing (ID). 1" Clamps required (not included). May be used with our Gator 2000 Drip Irrigation Kit. -
Drip Irrigation Parts and Supplies
1" Insert x 3/4" MPT Adapter is used to couple a 1" hose to a 3/4" FPT (female pipe thread) fitting. A 1" clamp is recommended at the hose side. -
Drip Irrigation Parts and Supplies
3/4" Hose Swivel attaches to a hose bib, faucet, spigot, hydrant, garden hose or hose threaded parts (like filters and pressure regulators) and accepts fittings with 3/4" male hose threads (MHT). -
Gilmour Metal Y Connector w/ Shut Off Valves is a great way to control water flow for two hoses. Longer legs prevents hose kinks at faucet. Chrome-plated zinc construction. -
U shaped wire hold downs are great for securing poly tubing, dripper line or drip tubing in place. Simple to use and work well in heavy soils. 6" long. 100 Pack. -
U shaped wire hold downs are great for securing poly tubing, dripper line or drip tubing in place. Simple to use and work well in heavy soils. 6" long. 10 Pack. -
Regulator / Tee Screen Assembly for Drip Irrigation
Regulator / Tee Screen Assembly connects drip tubing or distribution tubing to any ¾” garden hose thread water source. This pressure regulator has a maximum operating pressure of 15 PSI. Requires NO glue or tools for installation. To install tape-loc sides, simply turn sleeve counter-clockwise, slip tubing over barb, and turn sleeve clockwise to hand tighten for a secure fit. -
Drip Irrigation Assembly
Regulator / Screen Assembly connects drip tubing or distribution tubing to any ¾” garden hose thread water source. The pressure regulator has a maximum operating pressure of 15 PSI. Requires NO glue or tools for installation. To install tape-loc side, simply turn sleeve counter-clockwise, slip tubing over barb, and turn sleeve clockwise to hand tighten for a secure fit. -
Hose-End Tee Filter for Drip Irrigation Kits
Recommended to filter out particles common in well water that might clog the built-in emitters in drip tubing. This filter has a swivel FHT (female hose thread) inlet and MHT (male hose thread) outlet. The internal mesh screen filter may be removed for cleaning. When using with a drip irrigation garden kit, install this filter between your water source and the regulator/screen assembly included in each drip kit. -
Punch Tool for Drip Irrigation Kits
Ejector Style Hole Punch used for "punching" a hole in rigid poly tubing to insert 1/4" barb fittings. This punch is constructed of heavy duty plastic. It creates clean, precise holes for 1/4" barb fittings. Ejector pin quickly cleans the punch tool of debris. Included in our Gator 2000 Drip Kit as well as our Landscape 400 Drip Kit. -
Gator Drip Irrigation Kits
The Gator Fitting Pack consist of 2 Perma-Loc Tees, 1 Perma-Loc Elbow and 1 Perma-Loc Coupling. This pack allows customization of each Irri-Gator Drip Kit. Consists of commercial grade, UV resistant plastic. Requires NO glue or tools for installation. To install tape-loc side, simply turn sleeve counter-clockwise, slip tubing over barb, and turn sleeve clockwise to hand tighten for a secure fit. -
Drip Irrigation Parts and Supplies
In-Line valve for 5/8" ID tubing used to control water flow of individual lines. A valve can be easily installed directly into an individual row or into the mainline to control the water flow of more than one row. Consists of commercial grade, UV resistant plastic. Requires NO glue or tools for installation. The perfect accessory for our drip irrigation garden kits!! -
Drip Irrigation Parts and Supplies
Perma-Loc x 250 Barb / Valve for 5/8" ID Tubing, aka In-Line Barbed Valve for 5/8" ID tubing, is used to control water flow. A valve can be easily installed into the rigid poly mainline to control the water flow of an individual row. This barbed valve is the 250 Series. A punch tool is required for installation. Consists of commercial grade, UV resistant plastic. The perfect accessory for our Gator 2000 Drip Irrigation Garden Kit!! -
Drip Irrigation Fitting
This Perma-Loc x 250 Barb fitting connects 5/8" drip tubing or 5/8" distribution tubing to rigid poly tubing. Consists of commercial grade, UV resistant plastic. To install, simply turn sleeve counter-clockwise, slip tubing over barb, and turn sleeve clockwise to hand tighten for a secure fit. Use 1/4" punch tool make proper hole to insert barb fitting side into poly tubing. Gator 2000 Install Instructions -
Drip Irrigation Parts and Supplies
Perma-Loc Coupling to be used to either connect two pieces of Irri-Gator Drip Tubing or to repair an existing line. Consists of commercial grade, UV resistant plastic. Requires NO glue or tools for installation. Gator 100/250/1000 Drip Irrigation Kit Installation Instructions -
Drip Irrigation Parts and Supplies
Elbow fitting to be used with any Irri-Gator Drip Tubing or Distribution Tubing. Elbows allow you to make a sharp turn which the tubing itself is not capable of making. Consists of commercial grade, UV resistant plastic. Requires NO glue or tools for installation. To install, simply turn sleeve counter-clockwise, slip tubing over barb, and turn sleeve clockwise to hand tighten for a secure fit. Gator 100/250/1000 Installation Instructions -
Drip Irrigation Parts and Supplies
Perma-Loc Tee fitting to be used with any Irri-Gator Drip Tubing or Distribution Tubing. A tee can be used to branch off an additional line from the mainline or for an individual row. Consists of commercial grade, UV resistant plastic. Requires NO glue or tools for installation. To install, simply turn sleeve counter-clockwise, slip tubing over barb, and turn sleeve clockwise to hand tighten for a secure fit.