-
Drip Irrigation Fitting
1" Insert Coupling allows you to join two pieces of 1" tubing (ID). 1" Clamps required (not included). May be used with our Gator 2000 Drip Irrigation Kit. -
Drip Irrigation Fitting
This Perma-Loc x 250 Barb fitting connects 5/8" drip tubing or 5/8" distribution tubing to rigid poly tubing. Consists of commercial grade, UV resistant plastic. To install, simply turn sleeve counter-clockwise, slip tubing over barb, and turn sleeve clockwise to hand tighten for a secure fit. Use 1/4" punch tool make proper hole to insert barb fitting side into poly tubing. Gator 2000 Install Instructions -
Drip Irrigation Clamps
1" Clamp is a good general-purpose clamp. Diameter Range SAE is 11/16" to 1-1/4" (18mm t0 32mm). This clamp is also referred to as a worm drive hose clamp. -
Drip Irrigation Parts and Supplies
A backflow preventer is the effective and economical way to prevent the risk of back-flow contamination from outdoor hose bibb connected devices. It comes with a 3/4" FHT inlet and a 3/4" MHT outlet. No Teflon tape is required since both ends are hose thread. A standard hose washer is included to make a water tight seal. -
Drip Irrigation Parts and Supplies
Elbow fitting to be used with any Irri-Gator Drip Tubing or Distribution Tubing. Elbows allow you to make a sharp turn which the tubing itself is not capable of making. Consists of commercial grade, UV resistant plastic. Requires NO glue or tools for installation. To install, simply turn sleeve counter-clockwise, slip tubing over barb, and turn sleeve clockwise to hand tighten for a secure fit. Gator 100/250/1000 Installation Instructions -
Drip Irrigation Parts and Supplies
In-Line valve for 5/8" ID tubing used to control water flow of individual lines. A valve can be easily installed directly into an individual row or into the mainline to control the water flow of more than one row. Consists of commercial grade, UV resistant plastic. Requires NO glue or tools for installation. The perfect accessory for our drip irrigation garden kits!! -
Drip Irrigation Parts and Supplies
Perma-Loc x 250 Barb / Valve for 5/8" ID Tubing, aka In-Line Barbed Valve for 5/8" ID tubing, is used to control water flow. A valve can be easily installed into the rigid poly mainline to control the water flow of an individual row. This barbed valve is the 250 Series. A punch tool is required for installation. Consists of commercial grade, UV resistant plastic. The perfect accessory for our Gator 2000 Drip Irrigation Garden Kit!! -
Drip Irrigation Parts and Supplies
Perma-Loc Tee fitting to be used with any Irri-Gator Drip Tubing or Distribution Tubing. A tee can be used to branch off an additional line from the mainline or for an individual row. Consists of commercial grade, UV resistant plastic. Requires NO glue or tools for installation. To install, simply turn sleeve counter-clockwise, slip tubing over barb, and turn sleeve clockwise to hand tighten for a secure fit. -
U shaped wire hold downs are great for securing poly tubing, dripper line or drip tubing in place. Simple to use and work well in heavy soils. 6" long. 10 Pack. -
Drip Irrigation Fitting
1" Insert Plug, which is a 1" insert poly fitting, allows you to end a piece of 1" tubing (ID). A 1" clamp is required (not included) to secure the fitting to the tubing in case pressure is applied. -
Drip Irrigation Fitting
1" Insert Elbow allows you to make a 90° turn in 1" tubing (ID). 1" Clamps required (not included). May be used with our Gator 2000 Drip Irrigation Kit. -
Drip Irrigation Fitting
1" Insert Tee allows you to branch off an additional 1" line from the mainline or for an individual row. 1" Clamps required (not included). Included in our Gator 2000 Drip Irrigation Kit. -
Drip Irrigation Parts and Supplies
1" Insert x 3/4" MPT Adapter is used to couple a 1" hose to a 3/4" FPT (female pipe thread) fitting. A 1" clamp is recommended at the hose side. -
Drip Irrigation Parts and Supplies
3/4" Hose Swivel attaches to a hose bib, faucet, spigot, hydrant, garden hose or hose threaded parts (like filters and pressure regulators) and accepts fittings with 3/4" male hose threads (MHT). -
Drip Irrigation Assembly
Regulator / Screen Assembly connects drip tubing or distribution tubing to any ¾” garden hose thread water source. The pressure regulator has a maximum operating pressure of 15 PSI. Requires NO glue or tools for installation. To install tape-loc side, simply turn sleeve counter-clockwise, slip tubing over barb, and turn sleeve clockwise to hand tighten for a secure fit. -
Gilmour Metal Y Connector w/ Shut Off Valves is a great way to control water flow for two hoses. Longer legs prevents hose kinks at faucet. Chrome-plated zinc construction. -
Regulator / Tee Screen Assembly for Drip Irrigation
Regulator / Tee Screen Assembly connects drip tubing or distribution tubing to any ¾” garden hose thread water source. This pressure regulator has a maximum operating pressure of 15 PSI. Requires NO glue or tools for installation. To install tape-loc sides, simply turn sleeve counter-clockwise, slip tubing over barb, and turn sleeve clockwise to hand tighten for a secure fit. -
Hose-End Tee Filter for Drip Irrigation Kits
Recommended to filter out particles common in well water that might clog the built-in emitters in drip tubing. This filter has a swivel FHT (female hose thread) inlet and MHT (male hose thread) outlet. The internal mesh screen filter may be removed for cleaning. When using with a drip irrigation garden kit, install this filter between your water source and the regulator/screen assembly included in each drip kit. -
Gator Drip Irrigation Kits
The Gator Fitting Pack consist of 2 Perma-Loc Tees, 1 Perma-Loc Elbow and 1 Perma-Loc Coupling. This pack allows customization of each Irri-Gator Drip Kit. Consists of commercial grade, UV resistant plastic. Requires NO glue or tools for installation. To install tape-loc side, simply turn sleeve counter-clockwise, slip tubing over barb, and turn sleeve clockwise to hand tighten for a secure fit. -
Distribution Tubing for Drip Irrigation
Distribution tubing is also referred to as blank drip tubing. It does not have built-in emitters. To be used to bring water to the garden or for the mainline to avoid any unnecessary water usage. This 5/8" distribution tubing may be added to our Irri-Gator Drip Irrigation Garden Kits. All of our perma-loc fittings will work with this tubing. -
Are you looking for a mesh filter to prevent debris from passing into your 3/4″ water hose line?
The Irritec Mesh Screen Filter is an excellent choice. Irritec outfits these 3/4-Inch Hose Thread T-Filters with a 150-mesh stainless-steel screen. One side of the filter has a female hose swivel and the other has a male hose thread. Irritec T-Filters are excellent for connecting tubing to pumps, filters, or other irrigation projects. These filters fit onto any hose bib or garden hose end. Use them wherever your system requires a 90-degree turn in the head assembly components. Unfiltered water enters the T from the female side, passes through the internal filter, and exits through the exit point on the side of the filter. Irritec designs all its irrigation supplies with quality and versatility in mind. These handy T-filters make it easier than ever to customize your irrigation setup to fit your unique needs! -
Drip Irrigation Filter
3/4" Filter with Flush Cap and Stainless Steel 150 Mesh Screen. This filter is 3/4" MPT (Male Pipe Thread) at both inlet and outlet sides. -
Drip Tubing for Drip Irrigation Kits
Drip Tubing (100' Roll) has built-in emitters spaced every 12" for saturation coverage of desired area. Maximum working pressure of 15 PSI recommended. For use with Perma-Loc Fittings. Designed to ensure an even flow and minimize clogging of built-in emitters. Ideal for use in vegetable gardens and flowerbeds where the rows are straight. If your garden is in between the sizes of our Drip Irrigation Garden Kits, you can add extra drip tubing and perma-loc fittings to customize the irrigation system to your needs. -
Preset Pressure Regulator for Drip Irrigation Systems
The preset pressure regulator offers exceptional outlet pressure control to provide consistent performance from 1/2 to 12 gallons per minute. Both inlet and outlet are 3/4" FIPT. Included in our Gator 2000 Drip Kit due to extra thick industrial strength side walls. Made in the USA.
