-
Drip Irrigation Barb Plug
1/4" Barb Plug - Dual End A barb plug is used to plug holes from .075" to .225" in 1/2" supply tubing as well as capping off the end of 1/4" distribution tubing or 1/4" dripper line. -
Barb Connector for Drip Irrigation Kits
1/4" Barb Connector to be used with drip irrigation to either connect 1/4" drip tubing or 1/4" distribution tubing to 1/2" supply tubing or to extend the length of 1/4" tubing by acting as a coupling. Use a 1/4" punch tool to make the proper size hole in the supply tubing. This irrigation method works great in landscaping, hanging baskets, flower pots and garden boxes! -
Barb Tees for Drip Irrigation Kits
1/4" Barb Tee to be used with drip irrigation to either connect 1/4" drip tubing or 1/4" distribution tubing to branch off another line. It can also be inserted in 1/2" supply tubing. Use a 1/4" punch tool to make the proper size hole in the supply tubing. -
Drip Irrigation Figure Eight End Closure
Figure Eight End Closure for hose O.D. (outside diameter) up to .660". This fitting is the most common way to end a 1/2" supply line. Used in our Irri-Gator Landscape-400 Kit. -
Drip Irrigation Fitting
1/2" Insert Coupler (.620" OD), which is a 1/2" barb x 1/2" barb poly fitting, allows you to join two together pieces of 1/2" Supply Tubing or 1/2" Dripper Line. Due to the style and size of the tubing as, a clamp is not typically required. These fittings and tubing are for low pressure drip systems. -
Drip Irrigation Barb Poly Fitting
1/2" Insert Tee (.620" OD), which is a 1/2" barb x 1/2" barb x 1/2" barb poly fitting, allows you to branch off an additional 1/2″ line from the mainline or for an individual row. Due to the style and size of the tubing as, a clamp is not typically required. These fittings and tubing are for low pressure drip systems. -
Drip Irrigation Barb Poly Fitting
1/2" Insert Elbow (.620" OD), which is a 1/2" barb x 1/2" barb poly fitting, allows you to make a 90 degree turn while joining together two pieces of 1/2" Supply Tubing or 1/2" Dripper Line. Due to the style and size of the tubing as, a clamp is not typically required. Used with Drip Irrigation Landscape Kit. -
Drip Irrigation Adapter
1/2" Insert x 3/4" MPT (Male Pipe Thread) Adapter is used to couple a 1/2" hose to a 3/4" FPT (female pipe thread) fitting. Along with coupling the hose with a threaded fitting, it also reduces or increases in size between a 1/2" opening and a 3/4" opening. -
Drip Irrigation Parts and Supplies
Perma-Loc Coupling to be used to either connect two pieces of Irri-Gator Drip Tubing or to repair an existing line. Consists of commercial grade, UV resistant plastic. Requires NO glue or tools for installation. Gator 100/250/1000 Drip Irrigation Kit Installation Instructions -
Drip Irrigation Emitter
The .5 GPH Emitter (Pressure Compensating) delivers a consistent output of water, even with changes in pressure due to long runs of drip tubing or elevation changes. These emitters are self-flushing and less likely to clog than non-pressure compensating drippers. A removable top makes cleaning them simple. -
Drip Irrigation Fitting
1" Insert Coupling allows you to join two pieces of 1" tubing (ID). 1" Clamps required (not included). May be used with our Gator 2000 Drip Irrigation Kit. -
Coupling for Drip Irrigation Kits
3/4" Threaded Coupling is used to connect two fittings each with MPT (Male Pipe Thread). Used in our Irri-Gator Landscape-400 Kit. -
Drip Irrigation Fitting
This Perma-Loc x 250 Barb fitting connects 5/8" drip tubing or 5/8" distribution tubing to rigid poly tubing. Consists of commercial grade, UV resistant plastic. To install, simply turn sleeve counter-clockwise, slip tubing over barb, and turn sleeve clockwise to hand tighten for a secure fit. Use 1/4" punch tool make proper hole to insert barb fitting side into poly tubing. Gator 2000 Install Instructions -
Drip Irrigation Clamps
1" Clamp is a good general-purpose clamp. Diameter Range SAE is 11/16" to 1-1/4" (18mm t0 32mm). This clamp is also referred to as a worm drive hose clamp. -
Drip Irrigation Parts and Supplies
A backflow preventer is the effective and economical way to prevent the risk of back-flow contamination from outdoor hose bibb connected devices. It comes with a 3/4" FHT inlet and a 3/4" MHT outlet. No Teflon tape is required since both ends are hose thread. A standard hose washer is included to make a water tight seal. -
Drip Irrigation Fitting
1/2" Insert In-Line Valve (.620" OD) allows you to control water flow of individual lines. The valve connects sections of 1/2" Supply Tubing or 1/2" Dripper Line. A valve can be easily installed directly into an individual row or into the mainline to control the water flow of more than one row. Requires NO glue or tools for installation. -
Drip Irrigation Parts and Supplies
Elbow fitting to be used with any Irri-Gator Drip Tubing or Distribution Tubing. Elbows allow you to make a sharp turn which the tubing itself is not capable of making. Consists of commercial grade, UV resistant plastic. Requires NO glue or tools for installation. To install, simply turn sleeve counter-clockwise, slip tubing over barb, and turn sleeve clockwise to hand tighten for a secure fit. Gator 100/250/1000 Installation Instructions -
Drip Irrigation Parts and Supplies
In-Line valve for 5/8" ID tubing used to control water flow of individual lines. A valve can be easily installed directly into an individual row or into the mainline to control the water flow of more than one row. Consists of commercial grade, UV resistant plastic. Requires NO glue or tools for installation. The perfect accessory for our drip irrigation garden kits!! -
Drip Irrigation Parts and Supplies
Perma-Loc x 250 Barb / Valve for 5/8" ID Tubing, aka In-Line Barbed Valve for 5/8" ID tubing, is used to control water flow. A valve can be easily installed into the rigid poly mainline to control the water flow of an individual row. This barbed valve is the 250 Series. A punch tool is required for installation. Consists of commercial grade, UV resistant plastic. The perfect accessory for our Gator 2000 Drip Irrigation Garden Kit!! -
Drip Irrigation Parts and Supplies
Perma-Loc Tee fitting to be used with any Irri-Gator Drip Tubing or Distribution Tubing. A tee can be used to branch off an additional line from the mainline or for an individual row. Consists of commercial grade, UV resistant plastic. Requires NO glue or tools for installation. To install, simply turn sleeve counter-clockwise, slip tubing over barb, and turn sleeve clockwise to hand tighten for a secure fit. -
U shaped wire hold downs are great for securing poly tubing, dripper line or drip tubing in place. Simple to use and work well in heavy soils. 6" long. 10 Pack. -
Drip Irrigation Fitting
1" Insert Plug, which is a 1" insert poly fitting, allows you to end a piece of 1" tubing (ID). A 1" clamp is required (not included) to secure the fitting to the tubing in case pressure is applied. -
Drip Irrigation Fitting
1" Insert Elbow allows you to make a 90° turn in 1" tubing (ID). 1" Clamps required (not included). May be used with our Gator 2000 Drip Irrigation Kit. -
Drip Irrigation Fitting
1" Insert Tee allows you to branch off an additional 1" line from the mainline or for an individual row. 1" Clamps required (not included). Included in our Gator 2000 Drip Irrigation Kit. -
Sale!
Water your garden with the touch of a button. Adjustable water flow rate. Comes in 4 colors - Blue, red, black and green. If you have a preference, add a note to your order and we will do our best to accommodate you.
