-
Drip Irrigation Barb Plug
1/4" Barb Plug - Dual End A barb plug is used to plug holes from .075" to .225" in 1/2" supply tubing as well as capping off the end of 1/4" distribution tubing or 1/4" dripper line. -
Distribution Tubing for Drip Irrigation Kits
1/4" Distribution Tubing (no orifices) is most often branched off 1/2" dripper line or 1/2" supply tubing to individual plants with a drip emitter at the end. This tubing with no orifices may also be used as the mainline in smaller projects such as hanging baskets or small flower pot projects on decks and patios. -
Drip Irrigation Dripper Line
1/4" Dripper Line with 12" spacing of built-in emitters in a 100' roll. May be used to customize the Irri-Gator Landscape-400 Kit. This dripper line may be used in the following applications: Dense Plantings, Large Pots, Shrubs and Trees, and Gardens. -
Pressure Regulator for Drip Irrigation
Pressure Regulator 30 PSI is a preset pressure regulator with 3/4" FPT (female pipe thread) x 3/4" MPT (male pipe thread). Made in the USA. -
Drip Irrigation Assembly
Regulator / Screen Assembly connects drip tubing or distribution tubing to any ¾” garden hose thread water source. The pressure regulator has a maximum operating pressure of 15 PSI. Requires NO glue or tools for installation. To install tape-loc side, simply turn sleeve counter-clockwise, slip tubing over barb, and turn sleeve clockwise to hand tighten for a secure fit. -
Distribution Tubing for Drip Irrigation
Distribution tubing is also referred to as blank drip tubing. It does not have built-in emitters. To be used to bring water to the garden or for the mainline to avoid any unnecessary water usage. This 5/8" distribution tubing may be added to our Irri-Gator Drip Irrigation Garden Kits. All of our perma-loc fittings will work with this tubing. -
Regulator / Tee Screen Assembly for Drip Irrigation
Regulator / Tee Screen Assembly connects drip tubing or distribution tubing to any ¾” garden hose thread water source. This pressure regulator has a maximum operating pressure of 15 PSI. Requires NO glue or tools for installation. To install tape-loc sides, simply turn sleeve counter-clockwise, slip tubing over barb, and turn sleeve clockwise to hand tighten for a secure fit. -
Preset Pressure Regulator for Drip Irrigation Systems
The preset pressure regulator offers exceptional outlet pressure control to provide consistent performance from 1/2 to 12 gallons per minute. Both inlet and outlet are 3/4" FIPT. Included in our Gator 2000 Drip Kit due to extra thick industrial strength side walls. Made in the USA. -
Dripper Line for Drip Irrigation Kits
1/2" Dripper Line (.52 ID) with 12" spacing of built-in emitters in a 100' roll. May be used to customize the Irri-Gator Landscape-400 Kit. Clog resistant. -
Drip Irrigation Kit Tubing
1/2" Rigid Supply Tubing (no orifices) in a roll for Irri-Gator Landscape-400 Kit. Supply tubing allows you to get water to the desired locations in a conservative manner. You may use 1/2" insert fittings to extend the length of tubing (insert coupler), make a 90 degree angle (insert elbow) or add a row (insert tee) to your system. A punch tool may be used to insert an emitter in the supply tubing at the exact location of a planting. The 1/4" dripper line or 1/2" dripper line with 12" spacing may also be spurred from this supply tubing using 1/4" barbed fittings or 1/2" insert fittings, respectively. -
Drip Irrigation Figure Eight End Closure
Figure Eight End Closure for hose O.D. (outside diameter) up to .660". This fitting is the most common way to end a 1/2" supply line. Used in our Irri-Gator Landscape-400 Kit. -
Coupling for Drip Irrigation Kits
3/4" Threaded Coupling is used to connect two fittings each with MPT (Male Pipe Thread). Used in our Irri-Gator Landscape-400 Kit. -
Drip Irrigation Parts and Supplies
A backflow preventer is the effective and economical way to prevent the risk of back-flow contamination from outdoor hose bibb connected devices. It comes with a 3/4" FHT inlet and a 3/4" MHT outlet. No Teflon tape is required since both ends are hose thread. A standard hose washer is included to make a water tight seal. -
Drip Irrigation Parts and Supplies
3/4" Hose Swivel attaches to a hose bib, faucet, spigot, hydrant, garden hose or hose threaded parts (like filters and pressure regulators) and accepts fittings with 3/4" male hose threads (MHT). -
Drip Irrigation Emitter
The .5 GPH Emitter (Pressure Compensating) delivers a consistent output of water, even with changes in pressure due to long runs of drip tubing or elevation changes. These emitters are self-flushing and less likely to clog than non-pressure compensating drippers. A removable top makes cleaning them simple. -
Drip Irrigation Parts and Supplies
1" Insert x 3/4" MPT Adapter is used to couple a 1" hose to a 3/4" FPT (female pipe thread) fitting. A 1" clamp is recommended at the hose side. -
Drip Irrigation Parts and Supplies
Elbow fitting to be used with any Irri-Gator Drip Tubing or Distribution Tubing. Elbows allow you to make a sharp turn which the tubing itself is not capable of making. Consists of commercial grade, UV resistant plastic. Requires NO glue or tools for installation. To install, simply turn sleeve counter-clockwise, slip tubing over barb, and turn sleeve clockwise to hand tighten for a secure fit. Gator 100/250/1000 Installation Instructions -
Drip Irrigation Parts and Supplies
In-Line valve for 5/8" ID tubing used to control water flow of individual lines. A valve can be easily installed directly into an individual row or into the mainline to control the water flow of more than one row. Consists of commercial grade, UV resistant plastic. Requires NO glue or tools for installation. The perfect accessory for our drip irrigation garden kits!! -
Drip Irrigation Adapter
1/2" Insert x 3/4" MPT (Male Pipe Thread) Adapter is used to couple a 1/2" hose to a 3/4" FPT (female pipe thread) fitting. Along with coupling the hose with a threaded fitting, it also reduces or increases in size between a 1/2" opening and a 3/4" opening. -
Drip Irrigation Emitter (100 Pack)
The .5 GPH Emitter (Pressure Compensating) delivers a consistent output of water, even with changes in pressure due to long runs of drip tubing or elevation changes. These emitters are self-flushing and less likely to clog than non-pressure compensating drippers. A removable top makes cleaning them simple. -
Drip Irrigation Barb Poly Fitting
1/2" Insert Tee (.620" OD), which is a 1/2" barb x 1/2" barb x 1/2" barb poly fitting, allows you to branch off an additional 1/2″ line from the mainline or for an individual row. Due to the style and size of the tubing as, a clamp is not typically required. These fittings and tubing are for low pressure drip systems. -
Drip Irrigation Barb Poly Fitting
1/2" Insert Elbow (.620" OD), which is a 1/2" barb x 1/2" barb poly fitting, allows you to make a 90 degree turn while joining together two pieces of 1/2" Supply Tubing or 1/2" Dripper Line. Due to the style and size of the tubing as, a clamp is not typically required. Used with Drip Irrigation Landscape Kit. -
Drip Irrigation Fitting
1/2" Insert Coupler (.620" OD), which is a 1/2" barb x 1/2" barb poly fitting, allows you to join two together pieces of 1/2" Supply Tubing or 1/2" Dripper Line. Due to the style and size of the tubing as, a clamp is not typically required. These fittings and tubing are for low pressure drip systems. -
Punch-N-Cut Tool not only cuts rigid poly tubing, but also makes punching holes and inserting 1/4" barbed fittings & emitters almost effortless. All-In-One! It is a favorite among landscapers and commercial growers. This lightweight all-in-one tool is a great alternative to those frustrating days of keeping track of multiple tools! Punch N' Cut Tool has three major uses:- Cutting Tool - Cuts up to .94" mainline tubing with ease. Also cuts up to 1" PVC Schedule 40 with a little more effort required.
- PunchTool - Punches holes in 1/2" or larger mainline tubing for 1/4" fittings or emitters to be inserted.
- Insert Tool - Holds a barbed fitting and certain emitters to make installation easier. Less work for your fingers.
