-
Punch-N-Cut Tool not only cuts rigid poly tubing, but also makes punching holes and inserting 1/4" barbed fittings & emitters almost effortless. All-In-One! It is a favorite among landscapers and commercial growers. This lightweight all-in-one tool is a great alternative to those frustrating days of keeping track of multiple tools! Punch N' Cut Tool has three major uses:- Cutting Tool - Cuts up to .94" mainline tubing with ease. Also cuts up to 1" PVC Schedule 40 with a little more effort required.
- PunchTool - Punches holes in 1/2" or larger mainline tubing for 1/4" fittings or emitters to be inserted.
- Insert Tool - Holds a barbed fitting and certain emitters to make installation easier. Less work for your fingers.
-
Pressure Gauge Kit for Drip Irrigation Kit
If you would like to test the pressure of an individual line in your drip irrigation system, simply install this kit directly in the specific row or header of your choice. The pressure gauge included is a 0-100 psi Glycerin Liquid-Filled Gauge. This kit is compatible with our Irri-Gator Drip Irrigation Garden Kits. -
Drip Irrigation Parts and Supplies
A backflow preventer is the effective and economical way to prevent the risk of back-flow contamination from outdoor hose bibb connected devices. It comes with a 3/4" FHT inlet and a 3/4" MHT outlet. No Teflon tape is required since both ends are hose thread. A standard hose washer is included to make a water tight seal. -
Gardening Supplies
Groundskeeper II Rake is available in two sizes: The "Gardener" Rake has a 6" head with 8 steel tines and an 18" fiberglass handle weighing less than 2 pounds. The "Full Size" Rake has a 21" head with 28 steel tines and a 55" fiberglass handle weighing only 2 pounds. -
Pressure Regulator for Drip Irrigation
Pressure Regulator 30 PSI is a preset pressure regulator with 3/4" FPT (female pipe thread) x 3/4" MPT (male pipe thread). Made in the USA. -
Drip Irrigation Figure Eight End Closure
Figure Eight End Closure for hose O.D. (outside diameter) up to .660". This fitting is the most common way to end a 1/2" supply line. Used in our Irri-Gator Landscape-400 Kit. -
Drip Irrigation Barb Plugs
Barb Plugs - Dual End A barb plug is used to plug holes from .075" to .225" in 1/2" supply tubing as well as capping off the end of 1/4" distribution tubing or 1/4" dripper line. Pack of 100 Barb Plugs. -
Drip Irrigation Barb Plug
1/4" Barb Plug - Dual End A barb plug is used to plug holes from .075" to .225" in 1/2" supply tubing as well as capping off the end of 1/4" distribution tubing or 1/4" dripper line. -
Barb Tees for Drip Irrigation Kits
1/4" Barb Tee to be used with drip irrigation to either connect 1/4" drip tubing or 1/4" distribution tubing to branch off another line. It can also be inserted in 1/2" supply tubing. Use a 1/4" punch tool to make the proper size hole in the supply tubing. -
Barb Connector for Drip Irrigation Kits
1/4" Barb Connector to be used with drip irrigation to either connect 1/4" drip tubing or 1/4" distribution tubing to 1/2" supply tubing or to extend the length of 1/4" tubing by acting as a coupling. Use a 1/4" punch tool to make the proper size hole in the supply tubing. This irrigation method works great in landscaping, hanging baskets, flower pots and garden boxes! -
Preset Pressure Regulator for Drip Irrigation Systems
The preset pressure regulator offers exceptional outlet pressure control to provide consistent performance from 1/2 to 12 gallons per minute. Both inlet and outlet are 3/4" FIPT. Included in our Gator 2000 Drip Kit due to extra thick industrial strength side walls. Made in the USA. -
Drip Irrigation Emitter (100 Pack)
The .5 GPH Emitter (Pressure Compensating) delivers a consistent output of water, even with changes in pressure due to long runs of drip tubing or elevation changes. These emitters are self-flushing and less likely to clog than non-pressure compensating drippers. A removable top makes cleaning them simple. -
Drip Irrigation Emitter
The .5 GPH Emitter (Pressure Compensating) delivers a consistent output of water, even with changes in pressure due to long runs of drip tubing or elevation changes. These emitters are self-flushing and less likely to clog than non-pressure compensating drippers. A removable top makes cleaning them simple. -
Drip Irrigation Filter
3/4" Filter with Flush Cap and Stainless Steel 150 Mesh Screen. This filter is 3/4" MPT (Male Pipe Thread) at both inlet and outlet sides. -
2 Inch Plastic Filter with Flush Valve - Economy
- Filtering Element - 155 mesh stainless steel screen
- Constructed from chemical resistant polypropylene reinforced with fiber glass
- Pre-molded pressure taps
- Threaded cover closure - easy to use / no tools required
- Includes flush valve
-
Coupling for Drip Irrigation Kits
3/4" Threaded Coupling is used to connect two fittings each with MPT (Male Pipe Thread). Used in our Irri-Gator Landscape-400 Kit. -
Drip Irrigation Adapter
1/2" Insert x 3/4" MPT (Male Pipe Thread) Adapter is used to couple a 1/2" hose to a 3/4" FPT (female pipe thread) fitting. Along with coupling the hose with a threaded fitting, it also reduces or increases in size between a 1/2" opening and a 3/4" opening. -
Drip Irrigation Fitting
1/2" Insert In-Line Valve (.620" OD) allows you to control water flow of individual lines. The valve connects sections of 1/2" Supply Tubing or 1/2" Dripper Line. A valve can be easily installed directly into an individual row or into the mainline to control the water flow of more than one row. Requires NO glue or tools for installation. -
Drip Irrigation Barb Poly Fitting
1/2" Insert Tee (.620" OD), which is a 1/2" barb x 1/2" barb x 1/2" barb poly fitting, allows you to branch off an additional 1/2″ line from the mainline or for an individual row. Due to the style and size of the tubing as, a clamp is not typically required. These fittings and tubing are for low pressure drip systems. -
Drip Irrigation Barb Poly Fitting
1/2" Insert Elbow (.620" OD), which is a 1/2" barb x 1/2" barb poly fitting, allows you to make a 90 degree turn while joining together two pieces of 1/2" Supply Tubing or 1/2" Dripper Line. Due to the style and size of the tubing as, a clamp is not typically required. Used with Drip Irrigation Landscape Kit. -
Drip Irrigation Fitting
1/2" Insert Coupler (.620" OD), which is a 1/2" barb x 1/2" barb poly fitting, allows you to join two together pieces of 1/2" Supply Tubing or 1/2" Dripper Line. Due to the style and size of the tubing as, a clamp is not typically required. These fittings and tubing are for low pressure drip systems. -
Dripper Line for Drip Irrigation Kits
1/2" Dripper Line (.52 ID) with 12" spacing of built-in emitters in a 100' roll. May be used to customize the Irri-Gator Landscape-400 Kit. Clog resistant. -
Drip Irrigation Dripper Line
1/4" Dripper Line with 12" spacing of built-in emitters in a 100' roll. May be used to customize the Irri-Gator Landscape-400 Kit. This dripper line may be used in the following applications: Dense Plantings, Large Pots, Shrubs and Trees, and Gardens. -
Drip Irrigation Kit Tubing
1/2" Rigid Supply Tubing (no orifices) in a roll for Irri-Gator Landscape-400 Kit. Supply tubing allows you to get water to the desired locations in a conservative manner. You may use 1/2" insert fittings to extend the length of tubing (insert coupler), make a 90 degree angle (insert elbow) or add a row (insert tee) to your system. A punch tool may be used to insert an emitter in the supply tubing at the exact location of a planting. The 1/4" dripper line or 1/2" dripper line with 12" spacing may also be spurred from this supply tubing using 1/4" barbed fittings or 1/2" insert fittings, respectively. -
Distribution Tubing for Drip Irrigation Kits
1/4" Distribution Tubing (no orifices) is most often branched off 1/2" dripper line or 1/2" supply tubing to individual plants with a drip emitter at the end. This tubing with no orifices may also be used as the mainline in smaller projects such as hanging baskets or small flower pot projects on decks and patios. -
Drip Irrigation Clamps
1" Clamp is a good general-purpose clamp. Diameter Range SAE is 11/16" to 1-1/4" (18mm t0 32mm). This clamp is also referred to as a worm drive hose clamp. -
Drip Irrigation Fitting
1" Insert Tee allows you to branch off an additional 1" line from the mainline or for an individual row. 1" Clamps required (not included). Included in our Gator 2000 Drip Irrigation Kit. -
Drip Irrigation Fitting
1" Insert Plug, which is a 1" insert poly fitting, allows you to end a piece of 1" tubing (ID). A 1" clamp is required (not included) to secure the fitting to the tubing in case pressure is applied. -
Drip Irrigation Fitting
1" Insert Elbow allows you to make a 90° turn in 1" tubing (ID). 1" Clamps required (not included). May be used with our Gator 2000 Drip Irrigation Kit. -
Drip Irrigation Fitting
1" Insert Coupling allows you to join two pieces of 1" tubing (ID). 1" Clamps required (not included). May be used with our Gator 2000 Drip Irrigation Kit. -
Drip Irrigation Parts and Supplies
1" Insert x 3/4" MPT Adapter is used to couple a 1" hose to a 3/4" FPT (female pipe thread) fitting. A 1" clamp is recommended at the hose side. -
Drip Irrigation Parts and Supplies
3/4" Hose Swivel attaches to a hose bib, faucet, spigot, hydrant, garden hose or hose threaded parts (like filters and pressure regulators) and accepts fittings with 3/4" male hose threads (MHT). -
Gilmour Metal Y Connector w/ Shut Off Valves is a great way to control water flow for two hoses. Longer legs prevents hose kinks at faucet. Chrome-plated zinc construction. -
U shaped wire hold downs are great for securing poly tubing, dripper line or drip tubing in place. Simple to use and work well in heavy soils. 6" long. 100 Pack. -
U shaped wire hold downs are great for securing poly tubing, dripper line or drip tubing in place. Simple to use and work well in heavy soils. 6" long. 10 Pack. -
Sale!
Drip Irrigation Timer
Digital timer ideal for watering lawns, gardens, shrub areas, pots, hanging plants, patio irrigation and roof gardening. Galcon Timer Features:- 3/4" FHT inlet and MHT outlet
- 6 buttons with large integrated liquid crystal display
- Easy to read AM/PM clock and program
- Watering duration from 1 minute to 12 hours, in 1 minute increments
- Controller allows for weekly programs
- Starting times can be up to four times a day
- Powered by one 9-volt alkaline battery (not included)
-
Regulator / Tee Screen Assembly for Drip Irrigation
Regulator / Tee Screen Assembly connects drip tubing or distribution tubing to any ¾” garden hose thread water source. This pressure regulator has a maximum operating pressure of 15 PSI. Requires NO glue or tools for installation. To install tape-loc sides, simply turn sleeve counter-clockwise, slip tubing over barb, and turn sleeve clockwise to hand tighten for a secure fit. -
Drip Irrigation Assembly
Regulator / Screen Assembly connects drip tubing or distribution tubing to any ¾” garden hose thread water source. The pressure regulator has a maximum operating pressure of 15 PSI. Requires NO glue or tools for installation. To install tape-loc side, simply turn sleeve counter-clockwise, slip tubing over barb, and turn sleeve clockwise to hand tighten for a secure fit. -
Hose-End Tee Filter for Drip Irrigation Kits
Recommended to filter out particles common in well water that might clog the built-in emitters in drip tubing. This filter has a swivel FHT (female hose thread) inlet and MHT (male hose thread) outlet. The internal mesh screen filter may be removed for cleaning. When using with a drip irrigation garden kit, install this filter between your water source and the regulator/screen assembly included in each drip kit. -
Punch Tool for Drip Irrigation Kits
Ejector Style Hole Punch used for "punching" a hole in rigid poly tubing to insert 1/4" barb fittings. This punch is constructed of heavy duty plastic. It creates clean, precise holes for 1/4" barb fittings. Ejector pin quickly cleans the punch tool of debris. Included in our Gator 2000 Drip Kit as well as our Landscape 400 Drip Kit. -
Gator Drip Irrigation Kits
The Gator Fitting Pack consist of 2 Perma-Loc Tees, 1 Perma-Loc Elbow and 1 Perma-Loc Coupling. This pack allows customization of each Irri-Gator Drip Kit. Consists of commercial grade, UV resistant plastic. Requires NO glue or tools for installation. To install tape-loc side, simply turn sleeve counter-clockwise, slip tubing over barb, and turn sleeve clockwise to hand tighten for a secure fit. -
Drip Irrigation Parts and Supplies
In-Line valve for 5/8" ID tubing used to control water flow of individual lines. A valve can be easily installed directly into an individual row or into the mainline to control the water flow of more than one row. Consists of commercial grade, UV resistant plastic. Requires NO glue or tools for installation. The perfect accessory for our drip irrigation garden kits!! -
Drip Irrigation Parts and Supplies
Perma-Loc x 250 Barb / Valve for 5/8" ID Tubing, aka In-Line Barbed Valve for 5/8" ID tubing, is used to control water flow. A valve can be easily installed into the rigid poly mainline to control the water flow of an individual row. This barbed valve is the 250 Series. A punch tool is required for installation. Consists of commercial grade, UV resistant plastic. The perfect accessory for our Gator 2000 Drip Irrigation Garden Kit!! -
Drip Irrigation Fitting
This Perma-Loc x 250 Barb fitting connects 5/8" drip tubing or 5/8" distribution tubing to rigid poly tubing. Consists of commercial grade, UV resistant plastic. To install, simply turn sleeve counter-clockwise, slip tubing over barb, and turn sleeve clockwise to hand tighten for a secure fit. Use 1/4" punch tool make proper hole to insert barb fitting side into poly tubing. Gator 2000 Install Instructions -
Drip Irrigation Parts and Supplies
Perma-Loc Coupling to be used to either connect two pieces of Irri-Gator Drip Tubing or to repair an existing line. Consists of commercial grade, UV resistant plastic. Requires NO glue or tools for installation. Gator 100/250/1000 Drip Irrigation Kit Installation Instructions -
Drip Irrigation Parts and Supplies
Elbow fitting to be used with any Irri-Gator Drip Tubing or Distribution Tubing. Elbows allow you to make a sharp turn which the tubing itself is not capable of making. Consists of commercial grade, UV resistant plastic. Requires NO glue or tools for installation. To install, simply turn sleeve counter-clockwise, slip tubing over barb, and turn sleeve clockwise to hand tighten for a secure fit. Gator 100/250/1000 Installation Instructions -
Drip Irrigation Parts and Supplies
Perma-Loc Tee fitting to be used with any Irri-Gator Drip Tubing or Distribution Tubing. A tee can be used to branch off an additional line from the mainline or for an individual row. Consists of commercial grade, UV resistant plastic. Requires NO glue or tools for installation. To install, simply turn sleeve counter-clockwise, slip tubing over barb, and turn sleeve clockwise to hand tighten for a secure fit. -
Poly Tubing for Drip Irrigation Systems
Polyethylene distribution tubing does not have built-in emitters. This rigid 1" tubing may be used to bring water to the garden or for the mainline to avoid any unnecessary water usage. -
Drip Irrigation Tubing
5/8" Drip Tubing with built-in emitters spaced every 12” for saturation coverage of desired area. Designed to ensure an even flow and minimize clogging of built-in emitters. Flow rate is .5 GPM/100’. For use with Irri-Gator Drip Kits. Ideal for uses in vegetable gardens and flowerbeds where the rows are straight. -
Drip Tubing for Drip Irrigation Kits
Drip Tubing (100' Roll) has built-in emitters spaced every 12" for saturation coverage of desired area. Maximum working pressure of 15 PSI recommended. For use with Perma-Loc Fittings. Designed to ensure an even flow and minimize clogging of built-in emitters. Ideal for use in vegetable gardens and flowerbeds where the rows are straight. If your garden is in between the sizes of our Drip Irrigation Garden Kits, you can add extra drip tubing and perma-loc fittings to customize the irrigation system to your needs.
