-
Punch-N-Cut Tool not only cuts rigid poly tubing, but also makes punching holes and inserting 1/4" barbed fittings & emitters almost effortless. All-In-One! It is a favorite among landscapers and commercial growers. This lightweight all-in-one tool is a great alternative to those frustrating days of keeping track of multiple tools! Punch N' Cut Tool has three major uses:- Cutting Tool - Cuts up to .94" mainline tubing with ease. Also cuts up to 1" PVC Schedule 40 with a little more effort required.
- PunchTool - Punches holes in 1/2" or larger mainline tubing for 1/4" fittings or emitters to be inserted.
- Insert Tool - Holds a barbed fitting and certain emitters to make installation easier. Less work for your fingers.
-
Pressure Gauge Kit for Drip Irrigation Kit
If you would like to test the pressure of an individual line in your drip irrigation system, simply install this kit directly in the specific row or header of your choice. The pressure gauge included is a 0-100 psi Glycerin Liquid-Filled Gauge. This kit is compatible with our Irri-Gator Drip Irrigation Garden Kits. -
Drip Irrigation Parts and Supplies
A backflow preventer is the effective and economical way to prevent the risk of back-flow contamination from outdoor hose bibb connected devices. It comes with a 3/4" FHT inlet and a 3/4" MHT outlet. No Teflon tape is required since both ends are hose thread. A standard hose washer is included to make a water tight seal. -
Gardening Supplies
Groundskeeper II Rake is available in two sizes: The "Gardener" Rake has a 6" head with 8 steel tines and an 18" fiberglass handle weighing less than 2 pounds. The "Full Size" Rake has a 21" head with 28 steel tines and a 55" fiberglass handle weighing only 2 pounds. -
Pressure Regulator for Drip Irrigation
Pressure Regulator 30 PSI is a preset pressure regulator with 3/4" FPT (female pipe thread) x 3/4" MPT (male pipe thread). Made in the USA. -
Drip Irrigation Figure Eight End Closure
Figure Eight End Closure for hose O.D. (outside diameter) up to .660". This fitting is the most common way to end a 1/2" supply line. Used in our Irri-Gator Landscape-400 Kit. -
Drip Irrigation Barb Plugs
Barb Plugs - Dual End A barb plug is used to plug holes from .075" to .225" in 1/2" supply tubing as well as capping off the end of 1/4" distribution tubing or 1/4" dripper line. Pack of 100 Barb Plugs. -
Drip Irrigation Barb Plug
1/4" Barb Plug - Dual End A barb plug is used to plug holes from .075" to .225" in 1/2" supply tubing as well as capping off the end of 1/4" distribution tubing or 1/4" dripper line. -
Barb Tees for Drip Irrigation Kits
1/4" Barb Tee to be used with drip irrigation to either connect 1/4" drip tubing or 1/4" distribution tubing to branch off another line. It can also be inserted in 1/2" supply tubing. Use a 1/4" punch tool to make the proper size hole in the supply tubing. -
Barb Connector for Drip Irrigation Kits
1/4" Barb Connector to be used with drip irrigation to either connect 1/4" drip tubing or 1/4" distribution tubing to 1/2" supply tubing or to extend the length of 1/4" tubing by acting as a coupling. Use a 1/4" punch tool to make the proper size hole in the supply tubing. This irrigation method works great in landscaping, hanging baskets, flower pots and garden boxes! -
Preset Pressure Regulator for Drip Irrigation Systems
The preset pressure regulator offers exceptional outlet pressure control to provide consistent performance from 1/2 to 12 gallons per minute. Both inlet and outlet are 3/4" FIPT. Included in our Gator 2000 Drip Kit due to extra thick industrial strength side walls. Made in the USA. -
Drip Irrigation Emitter (100 Pack)
The .5 GPH Emitter (Pressure Compensating) delivers a consistent output of water, even with changes in pressure due to long runs of drip tubing or elevation changes. These emitters are self-flushing and less likely to clog than non-pressure compensating drippers. A removable top makes cleaning them simple. -
Drip Irrigation Emitter
The .5 GPH Emitter (Pressure Compensating) delivers a consistent output of water, even with changes in pressure due to long runs of drip tubing or elevation changes. These emitters are self-flushing and less likely to clog than non-pressure compensating drippers. A removable top makes cleaning them simple. -
Drip Irrigation Filter
3/4" Filter with Flush Cap and Stainless Steel 150 Mesh Screen. This filter is 3/4" MPT (Male Pipe Thread) at both inlet and outlet sides. -
2 Inch Plastic Filter with Flush Valve - Economy
- Filtering Element - 155 mesh stainless steel screen
- Constructed from chemical resistant polypropylene reinforced with fiber glass
- Pre-molded pressure taps
- Threaded cover closure - easy to use / no tools required
- Includes flush valve
-
Coupling for Drip Irrigation Kits
3/4" Threaded Coupling is used to connect two fittings each with MPT (Male Pipe Thread). Used in our Irri-Gator Landscape-400 Kit. -
Drip Irrigation Adapter
1/2" Insert x 3/4" MPT (Male Pipe Thread) Adapter is used to couple a 1/2" hose to a 3/4" FPT (female pipe thread) fitting. Along with coupling the hose with a threaded fitting, it also reduces or increases in size between a 1/2" opening and a 3/4" opening. -
Drip Irrigation Fitting
1/2" Insert In-Line Valve (.620" OD) allows you to control water flow of individual lines. The valve connects sections of 1/2" Supply Tubing or 1/2" Dripper Line. A valve can be easily installed directly into an individual row or into the mainline to control the water flow of more than one row. Requires NO glue or tools for installation. -
Drip Irrigation Barb Poly Fitting
1/2" Insert Tee (.620" OD), which is a 1/2" barb x 1/2" barb x 1/2" barb poly fitting, allows you to branch off an additional 1/2″ line from the mainline or for an individual row. Due to the style and size of the tubing as, a clamp is not typically required. These fittings and tubing are for low pressure drip systems. -
Drip Irrigation Barb Poly Fitting
1/2" Insert Elbow (.620" OD), which is a 1/2" barb x 1/2" barb poly fitting, allows you to make a 90 degree turn while joining together two pieces of 1/2" Supply Tubing or 1/2" Dripper Line. Due to the style and size of the tubing as, a clamp is not typically required. Used with Drip Irrigation Landscape Kit. -
Drip Irrigation Fitting
1/2" Insert Coupler (.620" OD), which is a 1/2" barb x 1/2" barb poly fitting, allows you to join two together pieces of 1/2" Supply Tubing or 1/2" Dripper Line. Due to the style and size of the tubing as, a clamp is not typically required. These fittings and tubing are for low pressure drip systems. -
Dripper Line for Drip Irrigation Kits
1/2" Dripper Line (.52 ID) with 12" spacing of built-in emitters in a 100' roll. May be used to customize the Irri-Gator Landscape-400 Kit. Clog resistant. -
Drip Irrigation Dripper Line
1/4" Dripper Line with 12" spacing of built-in emitters in a 100' roll. May be used to customize the Irri-Gator Landscape-400 Kit. This dripper line may be used in the following applications: Dense Plantings, Large Pots, Shrubs and Trees, and Gardens. -
Drip Irrigation Kit Tubing
1/2" Rigid Supply Tubing (no orifices) in a roll for Irri-Gator Landscape-400 Kit. Supply tubing allows you to get water to the desired locations in a conservative manner. You may use 1/2" insert fittings to extend the length of tubing (insert coupler), make a 90 degree angle (insert elbow) or add a row (insert tee) to your system. A punch tool may be used to insert an emitter in the supply tubing at the exact location of a planting. The 1/4" dripper line or 1/2" dripper line with 12" spacing may also be spurred from this supply tubing using 1/4" barbed fittings or 1/2" insert fittings, respectively. -
Distribution Tubing for Drip Irrigation Kits
1/4" Distribution Tubing (no orifices) is most often branched off 1/2" dripper line or 1/2" supply tubing to individual plants with a drip emitter at the end. This tubing with no orifices may also be used as the mainline in smaller projects such as hanging baskets or small flower pot projects on decks and patios. -
Drip Irrigation Clamps
1" Clamp is a good general-purpose clamp. Diameter Range SAE is 11/16" to 1-1/4" (18mm t0 32mm). This clamp is also referred to as a worm drive hose clamp. -
Drip Irrigation Fitting
1" Insert Tee allows you to branch off an additional 1" line from the mainline or for an individual row. 1" Clamps required (not included). Included in our Gator 2000 Drip Irrigation Kit. -
Drip Irrigation Fitting
1" Insert Plug, which is a 1" insert poly fitting, allows you to end a piece of 1" tubing (ID). A 1" clamp is required (not included) to secure the fitting to the tubing in case pressure is applied. -
Drip Irrigation Fitting
1" Insert Elbow allows you to make a 90° turn in 1" tubing (ID). 1" Clamps required (not included). May be used with our Gator 2000 Drip Irrigation Kit. -
Drip Irrigation Fitting
1" Insert Coupling allows you to join two pieces of 1" tubing (ID). 1" Clamps required (not included). May be used with our Gator 2000 Drip Irrigation Kit. -
Drip Irrigation Parts and Supplies
1" Insert x 3/4" MPT Adapter is used to couple a 1" hose to a 3/4" FPT (female pipe thread) fitting. A 1" clamp is recommended at the hose side. -
Drip Irrigation Parts and Supplies
3/4" Hose Swivel attaches to a hose bib, faucet, spigot, hydrant, garden hose or hose threaded parts (like filters and pressure regulators) and accepts fittings with 3/4" male hose threads (MHT). -
Gilmour Metal Y Connector w/ Shut Off Valves is a great way to control water flow for two hoses. Longer legs prevents hose kinks at faucet. Chrome-plated zinc construction. -
U shaped wire hold downs are great for securing poly tubing, dripper line or drip tubing in place. Simple to use and work well in heavy soils. 6" long. 100 Pack. -
U shaped wire hold downs are great for securing poly tubing, dripper line or drip tubing in place. Simple to use and work well in heavy soils. 6" long. 10 Pack. -
Sale!
Drip Irrigation Timer
Digital timer ideal for watering lawns, gardens, shrub areas, pots, hanging plants, patio irrigation and roof gardening. Galcon Timer Features:- 3/4" FHT inlet and MHT outlet
- 6 buttons with large integrated liquid crystal display
- Easy to read AM/PM clock and program
- Watering duration from 1 minute to 12 hours, in 1 minute increments
- Controller allows for weekly programs
- Starting times can be up to four times a day
- Powered by one 9-volt alkaline battery (not included)
-
Regulator / Tee Screen Assembly for Drip Irrigation
Regulator / Tee Screen Assembly connects drip tubing or distribution tubing to any ¾” garden hose thread water source. This pressure regulator has a maximum operating pressure of 15 PSI. Requires NO glue or tools for installation. To install tape-loc sides, simply turn sleeve counter-clockwise, slip tubing over barb, and turn sleeve clockwise to hand tighten for a secure fit. -
Drip Irrigation Assembly
Regulator / Screen Assembly connects drip tubing or distribution tubing to any ¾” garden hose thread water source. The pressure regulator has a maximum operating pressure of 15 PSI. Requires NO glue or tools for installation. To install tape-loc side, simply turn sleeve counter-clockwise, slip tubing over barb, and turn sleeve clockwise to hand tighten for a secure fit. -
Hose-End Tee Filter for Drip Irrigation Kits
Recommended to filter out particles common in well water that might clog the built-in emitters in drip tubing. This filter has a swivel FHT (female hose thread) inlet and MHT (male hose thread) outlet. The internal mesh screen filter may be removed for cleaning. When using with a drip irrigation garden kit, install this filter between your water source and the regulator/screen assembly included in each drip kit. -
Punch Tool for Drip Irrigation Kits
Ejector Style Hole Punch used for "punching" a hole in rigid poly tubing to insert 1/4" barb fittings. This punch is constructed of heavy duty plastic. It creates clean, precise holes for 1/4" barb fittings. Ejector pin quickly cleans the punch tool of debris. Included in our Gator 2000 Drip Kit as well as our Landscape 400 Drip Kit. -
Gator Drip Irrigation Kits
The Gator Fitting Pack consist of 2 Perma-Loc Tees, 1 Perma-Loc Elbow and 1 Perma-Loc Coupling. This pack allows customization of each Irri-Gator Drip Kit. Consists of commercial grade, UV resistant plastic. Requires NO glue or tools for installation. To install tape-loc side, simply turn sleeve counter-clockwise, slip tubing over barb, and turn sleeve clockwise to hand tighten for a secure fit. -
Drip Irrigation Parts and Supplies
In-Line valve for 5/8" ID tubing used to control water flow of individual lines. A valve can be easily installed directly into an individual row or into the mainline to control the water flow of more than one row. Consists of commercial grade, UV resistant plastic. Requires NO glue or tools for installation. The perfect accessory for our drip irrigation garden kits!! -
Drip Irrigation Parts and Supplies
Perma-Loc x 250 Barb / Valve for 5/8" ID Tubing, aka In-Line Barbed Valve for 5/8" ID tubing, is used to control water flow. A valve can be easily installed into the rigid poly mainline to control the water flow of an individual row. This barbed valve is the 250 Series. A punch tool is required for installation. Consists of commercial grade, UV resistant plastic. The perfect accessory for our Gator 2000 Drip Irrigation Garden Kit!! -
Drip Irrigation Fitting
This Perma-Loc x 250 Barb fitting connects 5/8" drip tubing or 5/8" distribution tubing to rigid poly tubing. Consists of commercial grade, UV resistant plastic. To install, simply turn sleeve counter-clockwise, slip tubing over barb, and turn sleeve clockwise to hand tighten for a secure fit. Use 1/4" punch tool make proper hole to insert barb fitting side into poly tubing. Gator 2000 Install Instructions -
Drip Irrigation Parts and Supplies
Perma-Loc Coupling to be used to either connect two pieces of Irri-Gator Drip Tubing or to repair an existing line. Consists of commercial grade, UV resistant plastic. Requires NO glue or tools for installation. Gator 100/250/1000 Drip Irrigation Kit Installation Instructions -
Drip Irrigation Parts and Supplies
Elbow fitting to be used with any Irri-Gator Drip Tubing or Distribution Tubing. Elbows allow you to make a sharp turn which the tubing itself is not capable of making. Consists of commercial grade, UV resistant plastic. Requires NO glue or tools for installation. To install, simply turn sleeve counter-clockwise, slip tubing over barb, and turn sleeve clockwise to hand tighten for a secure fit. Gator 100/250/1000 Installation Instructions -
Drip Irrigation Parts and Supplies
Perma-Loc Tee fitting to be used with any Irri-Gator Drip Tubing or Distribution Tubing. A tee can be used to branch off an additional line from the mainline or for an individual row. Consists of commercial grade, UV resistant plastic. Requires NO glue or tools for installation. To install, simply turn sleeve counter-clockwise, slip tubing over barb, and turn sleeve clockwise to hand tighten for a secure fit. -
Poly Tubing for Drip Irrigation Systems
Polyethylene distribution tubing does not have built-in emitters. This rigid 1" tubing may be used to bring water to the garden or for the mainline to avoid any unnecessary water usage. -
Drip Irrigation Tubing
5/8" Drip Tubing with built-in emitters spaced every 12” for saturation coverage of desired area. Designed to ensure an even flow and minimize clogging of built-in emitters. Flow rate is .5 GPM/100’. For use with Irri-Gator Drip Kits. Ideal for uses in vegetable gardens and flowerbeds where the rows are straight. -
Drip Tubing for Drip Irrigation Kits
Drip Tubing (100' Roll) has built-in emitters spaced every 12" for saturation coverage of desired area. Maximum working pressure of 15 PSI recommended. For use with Perma-Loc Fittings. Designed to ensure an even flow and minimize clogging of built-in emitters. Ideal for use in vegetable gardens and flowerbeds where the rows are straight. If your garden is in between the sizes of our Drip Irrigation Garden Kits, you can add extra drip tubing and perma-loc fittings to customize the irrigation system to your needs. -
Distribution Tubing for Drip Irrigation
Distribution tubing is also referred to as blank drip tubing. It does not have built-in emitters. To be used to bring water to the garden or for the mainline to avoid any unnecessary water usage. This 5/8" distribution tubing may be added to our Irri-Gator Drip Irrigation Garden Kits. All of our perma-loc fittings will work with this tubing. -
Landscape Drip Irrigation Kit
The “Irri-Gator Landscape” Micro Irrigation Kit is designed to meet your needs and includes all the essential micro components needed to install a drip irrigation system for your landscape area. The “Irri-Gator Landscape” Micro Irrigation System is comprised of two 100’ rolls of 1/2” micro tubing, one 100’ roll of 1/4” distribution tubing and one 100’ roll of 1/4” dripper tubing. The following fittings are also included in the kit: insert tees, elbows, couplers, in-line valves and enclosures. Also included are a filter, emitters, a punch tool and all other necessary connectors to complete the system. -
Drip Irrigation System
Once a garden exceeds 1,000 feet, gardeners are challenged to find a system that provides widespread irrigation while still being affordable. At only $311.33, the Gator 2000 drip irrigation kit can bring a steady flow of water to up to 20 rows of plants and soil reaching 100 feet in length each. For beginning to expert gardeners, our irrigation system has everything that you need to create the perfect garden getaway. We know that your garden is important to you, which means that it is important to us! -
Drip Irrigation System
Serious gardeners need a serious irrigation system, and the Gator 1000 system offers the perfect solution. Priced at only $192.63, the Gator 1000 is an expandable kit that waters up to 2,000 square feet. That’s as many as ten rows of 100’ each with as much as five feet between them. Have plans to grow a garden even further? No worries. The Gator 1000 can be expanded to provide irrigation to additional rows. You only need a pair of scissors for the installation – no special tools! This drip irrigation system comes with everything that you will need for installation and execution, delivering outstanding performance and quality when you need it the most, in your garden! We know that your garden is important to you, which means that it is important to us! -
Drip Irrigation System
For growing flower beds, the Gator 250 Drip Irrigation Kit offers an efficient, affordable irrigation solution. The kit can accommodate gardens of up to 500 square feet, allowing as many as six separate rows spaced as much as four feet from each other and spanning 38 feet in length each. Because kits can be expanded, homeowners can grow their gardens over time without having to purchase an entirely new kit. At a price of only $93.70, the Gator 250 also won’t stretch the family budget. So what are you waiting for? For a happy, healthy, beautiful garden, let our drip irrigation system help you create the garden that you've always dreamed of at a great price! -
Signature 1973 Whiz Head Rotary Sprinkler is ideal for riser installations in planting areas. It has a 1⁄2″ (1,27 cm) female threaded inlet. These sprinklers are made of high-impact corrosion-resistant plastic. Stainless steel bearing and large orifice nozzle. Made in the USA. -
Water your garden with the touch of a button. Adjustable water flow rate. Comes in 4 colors - Blue, red, black and green. If you have a preference, add a note to your order and we will do our best to accommodate you. -
This is a telescoping Gutter Cleaner that expands up to 5 feet. Spray away leaves and dirt easily. Easy On/Off Switch Comfortable Grip Handle Adjustable hook for easy cleaning and storage. Aluminum tubes and fittings. -
This compost is specially formulated to be an all natural, 100% organic fertilizer. LDK & Sons, LLC keeps your family in mind by keeping their products sustainable and safe to use without any worries! This can be used in gardens or containers. Directions for use: Gardens: Spread a uniform layer up to 2 inches on top of the soil, then mix in for best results. Containers: Mix 1 part compost with 2 parts of your favorite potting soil mix. -
Are you looking for a mesh filter to prevent debris from passing into your 3/4″ water hose line?
The Irritec Mesh Screen Filter is an excellent choice. Irritec outfits these 3/4-Inch Hose Thread T-Filters with a 150-mesh stainless-steel screen. One side of the filter has a female hose swivel and the other has a male hose thread. Irritec T-Filters are excellent for connecting tubing to pumps, filters, or other irrigation projects. These filters fit onto any hose bib or garden hose end. Use them wherever your system requires a 90-degree turn in the head assembly components. Unfiltered water enters the T from the female side, passes through the internal filter, and exits through the exit point on the side of the filter. Irritec designs all its irrigation supplies with quality and versatility in mind. These handy T-filters make it easier than ever to customize your irrigation setup to fit your unique needs! -
The Irrigator Hand Nozzle with 8 Spray Patterns with comfortable rubber grip- Shower
- Flat
- Jet
- Mist
- Cone
- Soaker
- Center
- Angle
-
Drip Irrigation Garden System
For flower beds smaller than 200 square feet, the Gator 100 irrigation kit is a great way to keep soil moist without using excess water. At a cost of only $59.85, the Gator 100 can bring irrigation to flower beds with as many as four separate rows spanning 22’ in length. Each row can be separated from the next by as much as four feet for the Gator 100 to be effective. To create your own small, personal slice of heaven right in your backyard, look no further than the Gator 100. Our irrigation systems will make your life easier and your plants healthier. Get yours today! -
This hand-held watering nozzle's design allows adjustment to the exact pattern of your lawn; ensuring the landscape is precisely watered with minimal overspray waste. 8 Spray patterns:- Shower
- Mist
- Soaker
- Angle
- Center
- Flat
- Cone
- Jet
-
Do you need to irrigate a pre-defined area? Do you want a sprinkler that is long-lasting, accurate, and durable? Bronze irrigation sprinklers are commonly used in irrigation systems to distribute water over a designated area. They are designed to provide a uniform spray pattern and can be adjusted to control the distance and angle of the water spray. Bronze sprinklers are typically attached to a water source, such as a hose or irrigation pipeline, and are connected to a system of pipes or tubing that deliver the water to the desired locations. Bronze sprinklers have been popular for irrigation systems due to several advantages they offer:- Durability: Bronze is a sturdy and long-lasting material, capable of withstanding outdoor conditions, including exposure to sunlight, heat, and moisture. This durability ensures that bronze sprinklers can endure extended periods of use without significant wear or damage.
- Corrosion resistance: Bronze is highly resistant to corrosion, making it suitable for use with different water qualities and irrigation applications. This resistance helps prevent the formation of rust and mineral deposits, which can clog the sprinkler and reduce its effectiveness.
- Heat resistance: Bronze has good heat resistance, allowing it to withstand high temperatures generated by the water passing through the sprinkler. This quality makes bronze sprinklers suitable for use in areas with intense sunlight or hot climates.
- Weight and stability: Bronze sprinklers tend to have a relatively heavier construction compared to plastic sprinklers. This added weight contributes to their stability, preventing them from shifting or moving during operation, even in windy conditions.
- Bronze material is highly resistant to impact
- Strong design and heavy construction for long life
- Robust spring to assure consistent and long lasting operation
- Smooth wetting pattern
- Good irrigation coverage and turn at low pressures
-
Do you need to irrigate a pre-defined area? Do you want a sprinkler that is long-lasting, accurate, and durable? Brass irrigation sprinklers are commonly used in irrigation systems to distribute water over a designated area. They are designed to provide a uniform spray pattern and can be adjusted to control the distance and angle of the water spray. Brass sprinklers are typically attached to a water source, such as a hose or irrigation pipeline, and are connected to a system of pipes or tubing that deliver the water to the desired locations. Brass sprinklers have been popular for irrigation systems due to several advantages they offer:- Durability: Brass is a sturdy and long-lasting material, capable of withstanding outdoor conditions, including exposure to sunlight, heat, and moisture. This durability ensures that brass sprinklers can endure extended periods of use without significant wear or damage.
- Corrosion resistance: Brass is highly resistant to corrosion, making it suitable for use with different water qualities and irrigation applications. This resistance helps prevent the formation of rust and mineral deposits, which can clog the sprinkler and reduce its effectiveness.
- Heat resistance: Brass has good heat resistance, allowing it to withstand high temperatures generated by the water passing through the sprinkler. This quality makes brass sprinklers suitable for use in areas with intense sunlight or hot climates.
- Weight and stability: Brass sprinklers tend to have a relatively heavier construction compared to plastic sprinklers. This added weight contributes to their stability, preventing them from shifting or moving during operation, even in windy conditions.
- Bronze material is highly resistant to impact
- Strong design and heavy construction for long life
- Robust spring to assure consistent and long lasting operation
- Smooth wetting pattern
- Good irrigation coverage and turn at low pressures
-
3/4″ Venturi Fertilizer Injector Assembly includes a Venturi injector, a suction line kit (a piece of water tube, a flow controller and a filter) and the fittings required to convert it to 3/4″ MHT x 3/4″ FHT to enable easy connection to a 3/4″ garden hose. This assembly can be used with our Gator 250 and Gator 1000 Drip Irrigation Kits. The Gator 100 is not large enough to enable the injector to work properly. We recommend a minimum flow rate of 1.5 gallons per minute. This kit now includes an atmospheric vacuum breaker, to prevent any potential backflow of fertilizer
